Brand: Computers Products

Product Code: C122-1006844

Availability:In stock

$22.78 22.78
OLED USB3.0 Tester 4-bit Voltage Current Power Capacity DetectorOLED USB3.0 Tester  is suitable for digital products, eg: mobile phone,power bank,USB flash drive and etc..Please don't use for engine and inductive load.Technical Parameter:Product model:USB 3.0 meter-H-white        Voltage range:DC03.70-13.00VVoltage accuracy:± (0.2% + 1words)             Current range:DC0.000-3.000ACurrent accuracy:± (0.8% + 3words)             Capacity accumulation:0-99999mAhCapacity resolution:1mAh                                Energy accumulation range: 0-99999mWh-999WhProduct weight:14g (package 46g)                Update rate:2 times/sIdle discharge:about 10mA                               Display screen:0.91" OLED screenPort mode: Compatibility: USB 2.0, USB 3.0     Product size:  64mm*21.6mm*11.2mm (L*W*H)Power :0-39.00WOperating instructions: When contact the power supply,  the screen shows welcome firstly and then displays current connection mode.Then it comes into the main interface. It has three connection modes: direct mode, quick charge mode and disconnected modeDirect mode is that the two middle signal wires are conducted directly. In this mode, USB port can transfer data normally.Quick charge mode is that the two middle signal wires are connected with the special charge chip.This chip can simulate quick charge agreement from different manufacturers to make different device matched automatically. So it can get quick charge.This mode can be compatible with more than 98% of intelligent device while the USB port cannot transfer data.Disconnected mode is that the two middle signal wires are disconnected. In this mode, USB port cannot transfer data.Mode SelectionKeep pressing the button first and then connect power supply.After the welcome window passed, you can set the three modes.When the mode you need appears, you can release the button.  The mode selection is done when you see the BLN flashes one time.Other Function of it:1.Current zero calibration function  The component aging and temperature variation after long-term use may appear tiny error when it measures small current.To avoid this error, you can keep pressing the button on the back to connect power supply in the no-load terms,until the three modes passes (as shown in the figure), then the LED lights. The calibration is accomplished2.Over-voltage and Under-voltage reminding function  When the voltage is over 5.3V (less than 4.7V), the arrow (up or down) will be flashing to remind the voltage is too high (low).When the voltage becomes to 4.7V-5.3V, the arrow will be disappeared.   In the main interface, you can click the button to switch data set one by one.And it provides for storing and checking 0 to 9 totally ten groups data set3.Capacity stored function  When data set is between the 1 to 9 group, the current capacity will be stored after power off.And the stored capacity will be accumulated after power on.When the data set is 0 group, the current capacity will be stored after power off. When power on next time, the stored mAh is blinking displayed .When the new mAh is up to 1 mAh, the stored mAh will be covered, and the values will start over4.Capacity unit switch function In the main interface, keep pressing the button, until the LED lights (time about 2s),release the button, the capacity will be switched between mAh and mWh.5.Screen rotation function In the main interface, keep pressing the button, until the LED lights and then goes out (time about 4s),release the button, the screen is rotated and automatically stored for being used next time conveniently.6.Shut-down screen function:In the main interface, keep pressing the button more than 6s, then release the button, the screen display can be shut-down and come into power saving mode.The LED is flashing in this moment and you can click the button to come back to the main interfaceTest PictureIs your power bank safe? Do you know how to calculate the capacity and efficiency of the mobile power bank battery?It is like that:Ah data * output voltage ÷battery voltage ÷ efficiency = mobile power bank battery Ah(output voltage is typically 5V, the battery voltage is generally based on 3.7V, typically by 85-90% efficiency)SizePaclage included:1 x tester1 x instructions